Plumbing Basics: A Prerequisite for Installing a Bathtub
Plumbing Basics: A Prerequisite for Installing a Bathtub
Blog Article
Are you currently in search of know-how about How to Install a Bathtub Yourself?
Installing a bath tub isn't exactly rocket science, yet it does call for solid plumbing, woodworking, as well as often, tiling skills. Replacing an old tub with a new one is additionally a moderately hard project. If the old tub is readily obtainable, the job can move rapidly; if you need to open up a wall to get rid of the old bathtub and also place the brand-new tub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will require a helper to move out the old tub and also set in the new one. Make certain you have certified on your own for the work and fit trying it. Instead of working with a contractor to take over a halfway-completed job, it is better to take into consideration employing one before you begin. Chances are you might need an expert plumber to make tube connections.
This post will assist you set up a new tub in your bathroom if you have currently acquired a new bathtub and do not need to transform the arrangement of your previous supply of water pipes.
Your tools and also material list ought to consist of the following:
Preparing for the Setup
Firstly, the sustaining frame supplied with the bath must be fitted (if required) according to the producer's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to make sure that if the faucet features a plastic washer, it is fitted between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets unit to avoid stress on the tub.
Fit the versatile faucet connectors to the bottom of the two taps using 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you utilize every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final setting.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installation, then the first thing you must do is detach the supply of water. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of getting rid of the existing faucets can be fairly problematic as a result of the limited accessibility that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the taps. Have a towel prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipes have actually been eliminated, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single taps from turning throughout this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old securing substance.
Before proceeding to fit the brand-new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, position the tub in the needed placement. The wooden boards are helpful in uniformly spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 tiny factors.
The next objective is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bath tub until the level reads level.
To set up faucets, fit all-time low of the outermost versatile tap adapter to the suitable supply pipeline by making a compression join; then do the exact same for the other tap.
Switch on the water and inspect all joints and brand-new pipework for leakages and tighten them if essential. Fill the bath tub and likewise check the overflow outlet and the normal outlet for leakages.
Finally, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the bath tub must wait up until the bathtub has actually been made use of at least when as this will settle it right into its last position.
Fitting New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to stop damages to the string. One end of the connector fits on the plastic tail of the tap and also the other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin making sure that the washing machines are in area between the faucet and the sink. Secure the faucet in place with the supplier offered backnut. Once the tap is safely in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap connectors. The previous type ought to be attached to the faucet finishes first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the installation can move sufficient to fracture a rigid seal, creating the water to permeate the wall surface between the bathroom as well as the tiling, leading to issues with moisture as well as possible leaks to the ceiling below.
You can pick from a selection of coloured sealants to blend in your fixtures and also installations. They are marketed in tubes and cartridges, as well as are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the bath tub with water before sealing, to allow for the movement experienced when the bathtub is in use. The sealant can fracture rather early if you do not think about this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently offered on the market. It is a good idea to fit the floor tiles utilizing water-resistant or water-proof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a reader on How to Install a Bathtub, I was thinking sharing that article post was a smart idea. Appreciated our posting? Please share it. Help another person check it out. Thanks so much for taking the time to read it.
Quality and quick, dial! Report this page